含多孔物质硝胺发射药的温感特性

研究了多孔物质对于硝胺发射药在不同初温下的燃面调节作用，由于多孔物质的孔结构及其与基体界面状况的改变，使发射药低温燃面增大，而高温燃面减小，这有利于降低燃速温度系数．     

Finite Element Analysis of a Moving Boundary Value Problem

A finite element formulation and the solution of a set of nonlinear coupled heat and mass transfer equations for a two-phase system with a moving evaporation interface is presented. The interface condition takes into account the moisture transfer balance at the moving boundary. The finite element results were compared with existing results for a single phase system for model validation. In the two-phase system, the movement of evaporation front has an appreciable effect on the temperature and moisture distribution inside the porous medium during drying. The effect of the nondimensional heat of vapourization parameter γ on the evaporation front, temperature and moisture distribution in porous medium was studied. The higher the value of γ, the slower is the movement of the evaporation front. The temperature decreased and the moisture content increased as the nondimensional vapourization parameter γ increased. This model has potential applications in studying the heat and mass transfer characteristics in food and biomaterials.     

核孔膜生产线膜微孔制备工艺实验研究

本文介绍核孔膜生产线,重点描述了膜微孔制备工艺的实验研究。对于PC和PES膜,已得到32种工况下的扩孔公式,其形式为D=A+Bt,其中D——孔径,t——扩孔时间,A,B为特定工艺参数下的常数值.通过实验。得到了膜孔密度N与300~#核反应堆功率P、热柱辐照位置L的经验公式,即N=6.97×10~5×10~3×101~(1.18L).在本生产线上可生产最大幅面为3 140mm×240mm,孔径为0.04～10 μm的多系列多规格的核孔膜产品。     

非均匀介质中的场与波：理论及其在电测井中的应用

本文综述了非均匀介质中场与波理论近年来的研究进展及其应用成果，着重介绍了非均匀介质中的电磁场正演分析和反演计算中的各种高效数值方法，以及它们在电法测井数值模拟和成象研究中的成功应用。     

Porous elastomeric beads from crosslinked emulsions

The production of porous polymeric particles is attractive for a large number of applications and can be achieved by various techniques. Although numerous production schemes exist for glassy polymers, difficulties arise for soft, rubbery materials that need a chemical crosslinking step, such as elastomers. This is particularly true for poly(dimethylsiloxane) (PDMS), which shows the lowest glass‐transition temperature among the polymers. Recent studies suggest in situ hydrogen bubble formation or vacuum drying of water droplets dispersed in the polymer matrix in order to generate porous PDMS structures. In this work we report early results based on the chemical crosslinking of water in PDMS emulsion droplets in a mechanically stirred thermostated water vessel. This approach is shown to lead to high porosity PDMS beads (ca. 10^?3 m particle diameter) with an open structure whose properties (diameter and porosity) are strongly influenced by the starting composition (solvent, surfactant, and polymer types and ratios), as well as the operating parameters (agitation and temperature). The possible uses of these derived beads are discussed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 967–971, 2002     

Asymmetric alumina membranes electrochemically formed in oxalic acid solution

Alumina membranes were fabricated by anodizing aluminium metal in 0.15 M oxalic acid. The growth kinetics of the porous layer were investigated in the temperature range –1 to 16 °C using linear potential scans up to 70 V. The faradaic efficiencies of metal oxidation and of porous layer formation, determined by applying Faraday's law, were found to be independent of both temperature and electrical charge. SEM analysis of the metal-side and solution-side surfaces revealed different morphologies. After dissolution of the barrier layer in phosphoric acid, the metal-side surface showed circular pores whose size of about 90 nm was found to be uniform and independent of temperature. The pore population was also practically independent of temperature and a value of about 4 × 10¹³ pores m^–2 was determined. On the solution-side surface the presence of a deposit partially occluding the mouths of pores was observed. This coating could be removed by chemical etching in NaOH or thermal treatment at 870 °C, where decomposition of oxalate occurs. This supports the hypothesis that the deposit consists of an aluminium salt containing oxalate anions precipitated from the solution. The results show that it is possible to control the morphological characteristics of the anodic alumina membranes by careful choice of experimental conditions.     

Advances in Microporous and Mesoporous Solids—Highlights of Recent Progress

This report highlights developments in the fields of microporous and mesoporous materials that were published mostly during the year 2002. Selected examples are provided to illustrate new zeolite structures, porous coordination materials, mesoporous solids with new compositions, controlled morphologies, and increased hydrothermal and thermal stabilities, as well as porous solids with tunable pore openings or other structural features that can be dynamically modified. A number of applications are discussed, including stabilization of reactive guests, separations, electronic materials, and sensors.     

部分可渗透直立圆柱的消波作用研究

本文导出了线性波浪作用于上部可渗透的直立刚性圆柱体上的水动力的解析解。在线性有势流的假定下，用特征函数展开方法求出了内部和外部流场的解。给出了不同波浪要素及结构尺寸参数下的数值结果。由结果可知，提高可渗透性可以有效消减波幅。     

多散射介质中光子密度波扩散方程的求解

将光源作为一个复数点光源,根据实验研究模型的要求,求解了多散射介质中光子密度波扩散方程,找出了与入射面相对应面的光子通量和介质中吸收系数改变量之间的关系。所得结论能直接用于多散射介质中成像问题的实验研究之中,即通过对光子通量的检测,反演出吸收系数改变量的分布,从而达到多散射介质中的成像问题的解决。     

Pad effects on material-removal rate in chemical-mechanical planarization

The role of a porous pad in controlling material-removal rate (MRR) during the chemical-mechanical planarization (CMP) process has been studied numerically. The numerical results are used to develop a phenomenological model that correlates the forces on each individual abrasive particle to the applied nominal pressure. The model provides a physical explanation for the experimentally observed domains of pressure-dependent MRR, where the pad deformation controls the load sharing between active-abrasive particles and direct pad-wafer contact. The predicted correlations between MRR and slurry characteristics, i.e., particle size and concentration, are in agreement with experimentally measured trends reported by Ouma¹ and Izumitani.²